Linear DVS-1200 User Manual download pdf (Page 27)

✦ To perform any of the advanced programming

steps, the Console must be in the Setup Mode.

✦ Each programming function is performed with

similar keystrokes. After the Console is in Setup

Mode, enter the programming step number,

press HOME, then enter the new value and press

AWAY. For reference, follow the ﬁ gures next to the

programming steps.

✴ If the new value is accepted, a “bing” will sound. If the new

value is not accepted, a “double buzz” will sound.

CONSOLE PROGRAMMING OPTIONS

STEP # PROGRAMMING FUNCTIONS POSSIBLE VALUES FACTORY VALUE INSTALLATION VALUE

25 ENTRY DELAY 20-255 SECONDS 30

26 EXIT DELAY 20-255 SECONDS 60

30 BURGLARY SIREN TIME 1-30 MINUTES 5

31 EMERGENCY SIREN TIME 1-30 MINUTES 5

32 FIRE SIREN TIME 1-30 MINUTES 5

40 AUTOMATION OUTPUT TIME 0-2500 SECONDS (0 = TOGGLE ON/OFF) 0

50 REMOTE ARMING MODE 2 = HOME MODE; 3 = AWAY MODE 3

51 REMOTE DISARMING MODE 0 = OFF MODE; 1 = CHIME MODE 0

61 ENTRY DELAY BEEPS 0 = OFF; 1 = ON 1

62 EXIT DELAY BEEPS 0 = OFF; 1 = ON 1

63 SILENT BURGLARY ALARM 0 = AUDIBLE; 1 = SILENT 0

64 SILENT EMERGENCY ALARM 0 = AUDIBLE; 1 = SILENT 0

65 QUICK ARMING 0 = OFF; 1 = ON 1

66 AUTO RESTORE 0 = OFF; 1 = ON 1

67 AUTO BYPASS 0 = OFF; 1 = ON 0

68 AUTOMATION MODE DURING ALARM

0 = FLASH (ENABLED BY FUNCTION 72)

1 = STEADY (ENABLED BY FUNCTION 72)

69 AUTOMATION BING TOME

0 = NO BINGS

1 = BINGS

70 REMOTE ARM/DISARM CHIRP

0 = NO CHIRPS

1 = CHIRPS (1 CHIRP = ARMED, 2 CHIRPS = DISARMED)

71 AUTOMATION FLASHES AFTER ALARM

0 = STANDARD

1 = FLASHING AFTER ALARM

72 AUTOMATION ACTIVE DURING ALARM

0 = STANDARD

1 = AUTOMATION ACTIVE DURING ALARM

(FLASH OR STEADY PROGRAMMED BY FUNCTION 68)

73 AUTOMATION ON WHILE ARMED

0 = STANDARD

1 = ON WHILE ARMED

74 AUTOMATION ON DURING EXIT/ENTRY

0 = STANDARD

1 = ON DURING EXIT/ENTRY DELAY

75 AUTOMATION POLARITY 0 = + WHEN OFF; 1 = + WHEN ON 1

87 REMOTE ACCESS PASSWORD 6 DIGITS 987654

92 DURESS CODE 1-5 DIGITS REMOVED

93 RESTRICTED USER CODE #1 1-5 DIGITS REMOVED

94 RESTRICTED USER CODE #2 1-5 DIGITS REMOVED

95 RESTRICTED USER CODE #3 1-5 DIGITS REMOVED

96 RESTRICTED USER CODE #4 1-5 DIGITS REMOVED

97 RESTRICTED USER CODE #5 1-5 DIGITS REMOVED

98 PAGE ALERT USER CODE 1-5 DIGITS REMOVED

99 MASTER USER CODE 1-5 DIGITS 1234

SETUP MODE

1. Start with the Console in Test Mode (Setup Mode

cannot be reached from any other mode).

2. From Test Mode, enter the master user code then

press TEST.

✎ NOTE: Only the master user code can be used to

put the system into the Setup Mode. The restricted

user codes cannot access Setup Mode, only Code

Mode.

✴ A “Gong” and ﬁ ve “Beeps” will sound, signaling that the

system is in Setup Mode.

3. After programming changes are complete, press

the OFF key for three seconds to exit Setup Mode.

✎ NOTE: If the system is left unattended in Setup

Mode, it will automatically switch back to Off Mode

after three minutes.

12. ADVANCED PROGRAMMING

HOME

TEST

= PROGRAM

= REMOVE

AWAY

= STORE

Console Programming Table

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 43 44

Comments to this Manuals

No comments

Linear DVS-1200 User Manual Page 27

Comments to this Manuals

Related products and manuals for Safety Linear DVS-1200