Linear DVS-1200 User Manual download pdf (Page 17)

DXS-31 & DXS-32 DOOR/WINDOW SENSORS

✦ The DXS-31 and DXS-32 sensors can be used

to monitor doors, windows, cabinets, crawl space

doors, gates, freezer doors, and many other moving

objects that could be used for intrusion or need to

be monitored.

✦ A built-in magnetic switch triggers the sensor when

its magnet (mounted on the moving part or the door

or window) moves away from the sensor.

✦ The DXS-31 sensor can be wired to external

normally closed switches for remote triggering.

✦ The DXS-31 sensor can connect directly to a glass

break detector.

SET SENSOR JUMPER

✦ A jumper inside the door/window sensor selects

instant or delayed response.

1A. If the sensor is going to be used on the primary

entry/exit door make sure that the jumper is in the

DELAY position.

1B. If the sensor is going to be used on a window or

a door that is not going to be used to enter and

exit the premises, set the jumper to the INSTANT

position.

CHOOSE MOUNTING METHOD

2A. Apply double-stick tape (supplied) to back of

sensors and magnets.

2B. Screws are also provided to mount sensors

and magnets. Screws are preferred over the

double-stick tape in permanent installations.

✎ UL NOTE: Double-stick tape is not allowed in UL

installations.

ATTACH SENSORS AND MAGNETS

✦ Allow a maximum of 1/2" between magnet and

sensor when door/window is closed.

✦ The magnet height is adjustable and an optional

magnet spacer is provided for uneven surfaces.

3B. On doors, mount sensor to door frame and

magnet to door.

3B. On windows, mount sensor to window frame and

magnet to window.

✎ NOTE: Magnet must line up with mark on sensor

case both horizontally & vertically.

4. Snap sensor onto mounting plate.

TEST SENSORS

✴ In Chime Mode, the Console should “ding-dong” when the

sensor sends a signal.

5. Open door or window.

✴ Verify that light on the sensor (if there is one) glows

momentarily when door/window is opened.

✴ Status indicator on the Console should remain lit for each

door/window sensor that is left open.

EXAMPLE INSTALLATION (WITH DXS-31 SHOWN)

TRANSMITTER

MOUNTED ON

DOOR JAMB

(NOTE: SMALL END

OF TRANSMITTER UP)

(NOTE: SMALL END

OF TRANSMITTER DOWN)

MAGNET

MOUNTED

ON DOOR

MAGNET MOUNTED

ON DOOR

TRANSMITTER

MOUNTED ON

WINDOW SILL

MAGNET MOUNTED

ON WINDOW FRAME

SLIDING WINDOW

LEFT OPENING DOOR

RIGHT OPENING DOOR

TRANSMITTER

MOUNTED ON

DOOR JAMB

TRANSMITTER

MOUNTED ON

WINDOW FRAME

MAGNET

MOUNTED

ON WINDOW

SASH STILE

DOUBLE-HUNG

WINDOW

TRANSMIT

INDICATOR

INPUT

SELECT

JUMPER

INSTANT/DELAY

OPTION JUMPER

ANTENNA

MAGNET

ALIGNMENT

MARK

TWO TYPE 2032

BATTERIES

BATTERY CLAMP

EXTERNAL

INPUT

TERMINALS

TEST

SWITCH

BATTERY

CLAMP

SCREW

INSTANT/DELAY

OPTION JUMPER

SELECTS

DELAY

SELECTS

INSTANT

ATTACH MOUNTING PLATES

USING THE SCREWS OR

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK

TAPE IS NOT ALLOWED IN UL INSTALLATIONS

1. PLACE RECEIVER INTO

PROGRAM OR "LEARN" MODE

2. ACTIVATE TRANSMITTER

BY OPENING DOOR OR

WINDOW

3. VERIFY THAT THE

RECEIVER ACCEPTED THE

SIGNAL

4. REPLACE TRANSMITTER

COVER WHEN FINISHED

NOTE: THE TRANSMIT

INDICATOR WILL ONLY LIGHT

DURING TRANSMISSIONS

WHEN THE CASE IS OPEN

(EXCEPT WHEN PUSHING

THE CASE FOR TESTING)

OPEN DOOR, TRANSMIT

INDICATOR SHOULD LIGHT

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 43 44

Comments to this Manuals

No comments

Linear DVS-1200 User Manual Page 17

Comments to this Manuals

Related products and manuals for Safety Linear DVS-1200