Linear DVS-1200 User Manual download pdf (Page 33)

ADDING ADDITIONAL USER CODES

✦ The Console can be programmed with ﬁ ve restricted

user codes and one page alert user code.

✦ The restricted user codes operate the system as

usual, but cannot access Setup Mode.

✦ The restricted user codes can access a special

Code Mode that can be used to change or remove

any of the ﬁ ve restricted user codes, the page alert

user code, or the duress code.

✦ The page alert user code dials the supervisory

number (programmed for a pager) when it is used

to arm or disarm the system.

✦ A restricted user code is appropriate to give any

user that should be restricted from programming

the Console.

✎ NOTE: For maximum security, a 3-5 digit code is

recommended.

✎ WARNING: NEVER PROGRAM ANY RESTRICTED

USER CODE THE SAME AS THE MASTER USER CODE!

STEPS #93-98 Create any additional user codes using these

steps then log the codes in the boxes to the right.

REMOVING ADDITIONAL USER CODES

STEPS #93-98 Any additional user code can be removed

from the Console by entering the appropriate step

number and pressing TEST.

✦ Because access to programming would be impossible

without a master user code, it cannot be removed

using these steps. The master user code can be

changed using programming STEP #99.

✎ NOTE: The master user code can be set to the

factory default using the Console master reset

programming step, although all other system

programming will be reset to factory values and all

sensors programmed will be erased.

CONSOLE MASTER RESET

✦ Master resetting the Console will set all of the

programming options back to the factory values. The

master user code will be reset to 1234.

✎ CAUTION: Master resetting the Console will erase the

user codes and remove all programmed sensors. All

Console and communicator programming values will

be reset to the factory defaults.

1. Start with the system in Test Mode (Setup Mode

cannot be reached from any other mode).

2. From Test Mode, enter the master user code then

press TEST.

✴ A “Gong” and ﬁ ve “Beeps” will sound, signaling that the

system is in Setup Mode.

3. Enter programming STEP #999 then press TEST.

4. Enter 999 again then press TEST again.

✴ A “Bing” will sound to indicate the beginning of the reset

process. This process will take up to 10 seconds while the

memory is being reset.

✦ The system will revert to the ﬁ rst time power-up

condition and the new master user code will be 1234.

Go to the “Basic Console Programming” section of

this manual to begin re-programming the system.

STEP CODE FUNCTION CODE ENTERED

STEP #93 RESTRICTED USER CODE #1

STEP #94 RESTRICTED USER CODE #2

STEP #95 RESTRICTED USER CODE #3

STEP #96 RESTRICTED USER CODE #4

STEP #97 RESTRICTED USER CODE #5

STEP #98 PAGE ALERT USER CODE

PROGRAMMING STEPS

#93 TO 98

PROGRAM

STORE PROGRAM

1-5 DIGIT CODE

(3-5 DIGITS RECOMMENDED)

WXY

TEST

KEYPAD CODE

PROGRAMMING STEPS

#92 TO 98

REMOVE

START IN TEST

MASTER

USER

CODE

1 GONG &

5 BEEPS

STEP #999

FOR

MASTER

RESET

DONE

PRESS TEST,

1 BING SOUNDS,

WAIT ABOUT 10

SECONDS

TEST

WXY

TEST

WXY

PRESS

TEST

WXY

TEST

WXY

ENTER 999

TO OK THE

MASTER

RESET

USE THESE EXAC

KEYSTROKES

TO PERFORM A

MASTER RESET

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 43 44

Comments to this Manuals

No comments

Linear DVS-1200 User Manual Page 33

Comments to this Manuals

Related products and manuals for Safety Linear DVS-1200