Linear DVS-1200 User Manual download pdf (Page 37)

COMMUNICATOR REPORTING OPTIONS

REPORTING FORMAT

✦ The factory setting causes the communicator to

report using the 4 BY 2 FORMAT. This format allows

four-digit account numbers from 0000 to 9999 and

provides two-digit alarm codes.

STEP #105 ADEMCO CONTACT ID can be chosen as a reporting

format using this step. This format allows 4-digit

account numbers from 0000 to 9999 and provides

verbose report descriptions with Ademco Contact ID

compatible Central Stations.

CALL ROUTING

✦ The communicator can be programmed with three

telephone numbers; primary, secondary, and

supervisory.

✦ The factory setting for the communicator is to

route all calls to the primary telephone number. If

communication is unsuccessful after ﬁ ve attempts

to the primary number, the secondary number

will be dialed for an additional ﬁ ve attempts. If

the secondary number cannot be reached, the

communicator will “sleep” for ﬁ ve minutes before

starting the call process over again. A total of four

sleep cycles (50 call attempts) can occur before the

communicator stops calling.

STEP #86 The communicator can be programmed to report

supervisory events (low battery, trouble, AC failure,

etc.) to the supervisory telephone number instead

of the primary or secondary telephone numbers

using this step.

Communicator Reporting Option Table

✎ CAUTION: If the page alert user code feature

is going to be used, the supervisory number is

reserved for the pager number. DO NOT SET THE

CALL ROUTING OPTION TO “1”.

✎ NOTE: To disable supervisory reports, set call

routing option to “1” and remove the supervisory

telephone number.

✎ NOTE: Do not program the primary and secondary

telephone numbers the same. See the FCC

Telephone Rules and Regulations on the rear

cover of this manual.

COMMUNICATOR REPORTING OPTIONS

STEP

PROGRAMMING

FUNCTION

POSSIBLE

VALUES

FACTORY

VALUE

INSTALLATION

VALUE

86 CALL ROUTING

0 = ALL CALLS TO PRIMARY OR SECONDARY NUMBER

1 = ALL ALARM CALLS TO PRIMARY OR SECONDARY NUMBER AND ALL

OTHERS TO SUPERVISORY NUMBER

88 ACCOUNT NUMBER 4 DIGITS EMPTY

89 PRIMARY PHONE NUMBER UP TO 20 DIGITS EMPTY

90 SECONDARY PHONE NUMBER UP TO 20 DIGITS EMPTY

91 SUPERVISORY/PAGER PHONE NUMBER UP TO 20 DIGITS EMPTY

PRESSING THE (A) KEY INSERTS A 1-SECOND DELAY

THE [FIRE] KEY INSERTS A 5-SECOND DELAY

FOR ALL PHONE NUMBERS ⇒ ⇒ ⇒ THE [CHIME] KEY INSERTS A “

”

THE (A) KEY INSERTS A “#” IF IT IS THE LAST DIGIT OF THE PHONE NUMBER

105 REPORTING FORMAT 0 = 4 BY 2; 1 = ADEMCO 0

108 REPORT SYSTEM TROUBLE 0 = NO; 1 = YES 0

110 REPORT FORCE ARMING 0 = NO; 1 = YES 0

111 OPEN/CLOSE 0 = NO; 1 = YES; 2 = MASTER PAC ONLY 0

113 POINT ID REPORTING FOR 4 BY 2 FORMAT 0 = NO; 1 = YES 1

JKL

HOME

AWAY

0 FOR 4 BY 2

1 FOR ADEMCO CONTACT ID

PROGRAMMING STEP #105

PROGRAM

STORE PROGRAM

TUV

MNO

HOME

AWAY

PROGRAMMING STEP #86

PROGRAM

STORE PROGRAM

0 FOR ALL TO PRIMARY/SECONDARY

1 FOR ALARMS ONLY TO

PRIMARY/SECONDARY

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 43 44

Comments to this Manuals

No comments

Linear DVS-1200 User Manual Page 37

Comments to this Manuals

Related products and manuals for Safety Linear DVS-1200