Linear AE-100 User Manual download pdf (Page 21)

PPN 30

30#SUB-UNITS#5#

SUB-UNITS = EACH SUB-UNIT NUMBER (2-4) TO COPY

ACCESS DATA TO IN A MULTI-UNIT INSTALLATION

COPY ACCESS DATA ONLY FROM MASTER TO SUB-UNITS

PPN 34

34#SUB-UNITS#5#

SUB-UNITS = EACH SUB-UNIT NUMBER (2-4) TO COPY

ALL DATA TO IN A MULTI-UNIT INSTALLATION

COPY ALL DATA FROM MASTER TO SUB-UNITS

PPN 35

35#MESSAGE#CLEAR#

MESSAGE = ERROR MESSAGE DISPLAYED

CLEAR = 5 TO CLEAR ERROR LOG

CLEAR = # TO EXIT WITHOUT CLEARING ERROR LOG

DISPLAY/CLEAR SYSTEM ERRORS

STANDARD PROGRAMMING METHOD

NOTE:

TO ALLOW FOR MULTI-UNIT NETWORK COMMUNICATIONS,

WHEN EXECUTING THIS COMMAND REMOTELY OVER THE

TELEPHONE, THE SYSTEM WILL DISCONNECT YOUR CALL

AFTER STEP #3 THEN COPY THE DATA FROM THE MASTER

UNIT TO THE SUB-UNITS.

NOTE:

TO ALLOW FOR MULTI-UNIT NETWORK COMMUNICATIONS,

WHEN EXECUTING THIS COMMAND REMOTELY OVER THE

TELEPHONE, THE SYSTEM WILL DISCONNECT YOUR CALL

AFTER STEP #3 THEN COPY THE DATA FROM THE MASTER

UNIT TO THE SUB-UNITS.

System Utility Commands

Several utility commands are available for the system. Utility commands

can be used to copy data to other units in a multi-unit installation, clear

memory, display system information, and control the relays.

For each of the following steps, enter the Master Password and enter

Programming Mode (if the unit is not already in that mode). Exit

Programming Mode when all programming is complete.

Copy Access Data Only from Master to Sub-units

To synchronize programming in multi-unit installations, the Directory

Entries and Stand-alone Entry Codes can be copied from the master unit

to selected sub-units.

✦ NOTE: PPN numbers 71 and 7 must be programmed before this command

will operate.

✦ NOTE: This utility command can only be performed from the “master” unit.

CAUTION: This utility command will overwrite ALL the access data in the

selected sub-units.

1. Press

2. Enter the unit number(s) of all of the sub-units to receive the access data.

Examples:

To copy to unit two only enter •

To copy to unit three only enter •

To copy to units two & three enter •

To copy to units two, three, and four enter •

3. To execute the command, enter

or enter

to exit (any other

entry will abort the command).

Copy All Data from Master to Sub-units

To synchronize programming in multi-unit installations, all system data

can be copied from the master unit to selected sub-units. This data

includes the Directory Entries, Stand-alone Entry Code data, and all

system option settings (except the sub-unit number and password).

✦ NOTE: PPN numbers 71 and 7 must be programmed before this command

will operate.

✦ NOTE: This utility command can only be performed from the “master” unit.

CAUTION: This utility command will overwrite ALL the data in the selected

sub-units.

1. Press

2. Enter the unit number(s) of all of the sub-units to receive the full data set.

Examples:

To copy to unit two only enter •

To copy to unit three only enter •

To copy to units two & three enter •

To copy to units two, three, and four enter •

3. To execute the command, enter

or enter

to exit (any other

entry will abort the command).

Display/Clear System Errors

The system’s power indicator will ﬂ ash if any system errors occur. These

errors include loss of AC power and low backup battery. In multi-unit

installations, the master unit logs communication errors with sub-units.

✦ NOTE: This step cannot be performed remotely through the telephone.

1. Press

2. The display will show any errors pending.

3. Press

to display the next error message (if any).

4. When there are no more error messages to be displayed, the system will

display “Clear Error Log?”.

5. Enter

to clear the error log - or - enter

to exit.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 35 36

Comments to this Manuals

No comments

Linear AE-100 User Manual Page 21

Comments to this Manuals

Related products and manuals for Door intercom systems Linear AE-100