Linear AE-100 User Manual download pdf (Page 12)

Optional Postal Lock

A postal lock can be installed in the AE-100 Entry System to provide

keyed access for the postal service. The AE-100 case is designed to

accept a U.S. Postal Service postal lock. When the postal lock is engaged

the access relay will activate.

Postal Lock Installation

1. Remove the four locknuts that retain the postal lock cover plate

and block (above the speaker on the AE-100 faceplate).

2. Remove the cover plate and block from the

four studs. Discard the plate and block.

3. Remove the faceplate’s postal lock hole plug. Discard the plug.

4. Install the postal lock assembly onto the four

studs. The postal lock’s moving plunger should

point towards the microswitch (see ﬁ gure).

5. Secure the postal lock with the four locknuts.

✦ NOTE: Be sure the postal lock’s plunger actuates the microswitch.

Adjust the postal lock and test the action until the microswitch fully

actuates.

6. Tighten the four locknuts after the adjustment

and testing is complete.

Optional Color CCTV Camera

Linear’s Model CCM-1 (P/N ACP00904) CCTV camera can be installed

inside the AE-100 Entry System. The camera provides a video signal for

viewing the area in front of the entry system.

The CAMERA connector is used to connect the camera to the AE-100.

The 4-conductor cable routes power to, and video from the camera.

The VIDEO OUT jack is the camera output for connection to a video

cable with a Type “BNC” connector. Up to 400 feet of 75-ohm RG-59

video cable can be used. Longer cable runs may require the use of a

video ampliﬁ er.

✦ NOTE: The composite video signal can be viewed on a video

monitor. Alternately, a Linear ChannelPlus brand video modulator

can be used to convert the video signal to an RF signal for

installations where the camera’s picture will be viewed on television

sets tuned to a custom channel.

Camera Installation

1. Remove the two locknuts and the cover plate from the camera

mounting studs on the AE-100 faceplate. Discard the cover plate.

✦ NOTE: A spare camera protection lens is supplied with the CCM-1

camera kit. If the AE-100’s protection lens needs replacing due to

vandalism, push the damaged protection lens out of the faceplate

and install the spare protection lens before installing the camera.

2. Mount the camera assembly on the two studs, with

the alignment hole in the camera bracket towards the

top. Secure the camera with the two locknuts.

3. Connect the camera’s cable to the AE-100’s CAMERA connector.

4. Connect the video cable to the AE-100’s VIDEO OUT connector.

5. Connect the other end of the video cable to the viewing monitor,

ChannelPlus brand video modulator, or video distribution system.

REMOVE LOCKNUTS

REMOVE PLATE & PLUG

INSTALL POSTAL LOCK

PLUNGER POINTS

TO MICROSWITCH

REPLACE LOCKNUTS

NOTE:

BE SURE THE POSTAL LOCK'S PLUNGER ACTUATES THE

MICROSWITCH. ADJUST THE POSTAL LOCK MOUNTING THEN

TEST THE ACTION UNTIL THE MICROSWITCH FULLY ACTUATES

INSPECT MICROSWITCH ACTION

CONNECT WIRING HARNESS

TO CAMERA CONNECTOR

REMOVE THE LENS CAP ATTACH CAMERA WITH TWO NUTS

REMOVE PLATE RETAINING NUTS

REMOVE THE PLATE

DRESS WIRES

WITH WIRE

TIES

CONNECT VIDEO CABLE TO

VIDEO OUT CONNECTOR

ALIGNMENT

HOLE

CAMERA

PROTECTION

LENS

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 35 36

Comments to this Manuals

No comments

Linear AE-100 User Manual Page 12

Comments to this Manuals

Related products and manuals for Door intercom systems Linear AE-100