Linear AE-100 User Manual download pdf (Page 15)

Programming Over the Telephone

Most system commands can be programmed using a TouchTone™

telephone. The telephone’s keypad will act similar to the AE-100’s keypad.

Both programming methods can be used over the telephone.

Connecting with a Telephone

1. Place a call to the telephone number of the

line that the AE-100 is connected to.

2. The AE-100 will answer on the third ring.

3. The system sounds beeps indicating the current system

status (including any other units in a multi-unit installation):

One short beep sounds if all access relays are activated (all •

doors open).

Two short beeps sound if all access relays are deactivated (all •

doors closed).

One long beep sounds if there is a combination of access relays •

activated and deactivated (some doors open, some doors

closed).

4. Enter the unit number (1-4) of the unit to log onto then press

In a single-unit installation, use the default unit number 1.

✦ NOTE: Log on to the Master Unit #1 in a multi-unit installation to

program the master’s memory. The master’s memory can then be

copied to the other units.

5. Enter the Master Password for the unit

(the factory setting is 123456).

6. To program using the Standard Programming Method press

To program using the Alternate Programming Method press

If the password is correct, the system will sound two short beeps.

7. Programming commands can now be entered

from the telephone’s keypad.

To program the system, refer to the following pages of this manual.

The Standard Programming Method steps are shown on •

Pages 16-22.

The Alternate Programming Method steps are shown on •

Pages 23-31.

Telephone Audio Prompts

When programming over the telephone, each programming step consists

of entering programming data using the telephone’s keypad. The system

will sound beeps over the telephone to indicate correct or incorrect

entries.

The audio prompts that give feedback during programming are different

for each programming method. Those differences are shown in the table

to the right.

Re-entering a Command After a Mistake

If an incorrect entry, or an incorrect key is pressed during programming,

press

and start the programming step over again.

Exiting Programming Mode

After programming, be sure to exit Programming Mode.

✦ NOTE: The AE-100 will automatically exit Programming Mode

after two minutes of programming inactivity.

To exit programming • when using the Standard Programming

Method, press:

To exit programming when using the Alternate Programming •

Method, press:

1. CALL THE SYSTEM

2. SYSTEM ANSWERS ON THIRD RING

3. SYSTEM SOUNDS THE CURRENT STATUS:

> ONE SHORT BEEP - ALL RELAYS ON

> TWO SHORT BEEPS - ALL RELAYS OFF

> ONE LONG BEEP - RELAYS MIXED ON & OFF

4. ENTER THE UNIT NUMBER (1-4) AND PRESS #

FOR SINGLE-UNIT INSTALLATIONS ENTER 1#

5. ENTER THE MASTER PASSWOR

(

DEFAULT PASSWORD IS 123456)

6. TO USE STANDARD PROGRAMMING PRESS #

TO USE ALTERNATE PROGRAMMING PRESS STAR

7. BEGIN PROGRAMMING, ENTER STEP NUMBER

FOLLOWED BY #

CONNECTING WITH A TELEPHONE

AUDIO PROMPTS FOR EACH PROGRAMMING METHOD

CONDITION

ALTERNATE

METHOD

SOUND

STANDARD

METHOD

SOUND

AFTER AN INCORRECT ENTRY

TWO

LONG

BEEPS

ONE

LONG

BEEP

AFTER A CORRECT ENTRY OF AN

INTERIM STEP

ONE

SHORT

BEEP

TWO

SHORT

BEEPS

AFTER A COMPLETE COMMAND

HAS BEEN ENTERED CORRECTLY

TWO

SHORT

BEEPS

THREE

SHORT

BEEPS

EXITING PROGRAMMING MODE

THREE

SHORT

BEEPS

SOUND

TO EXIT PROGRAMMING

STANDARD PROGRAMMING METHOD

PRESS

ALTERNATE PROGRAMMING METHOD

PRESS

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 35 36

Comments to this Manuals

No comments

Linear AE-100 User Manual Page 15

Comments to this Manuals

Related products and manuals for Door intercom systems Linear AE-100