Linear SLC User Manual download pdf (Page 28)

SLR • SLC • SLD Slide Gate Operator Installation Guide - 26 - 227968 Revision X19 8-11-2011

Gate Operation

Open Button

Opens the gate. If the Controller is programmed to stop

opening the gate at mid-travel, a constant press of the OPEN

button will override the Mid-travel Stop and completely open

the gate. If the Auto Close Timer is set, it will be suspended

until the OPEN button is released.

Close Button

Closes the gate if the gate is open. Also closes the gate if

the gate is in the process of opening.

Stop Button

Stops the gate from opening or closing at any time.

Single Input

Opens the gate if it’s closed and closes the gate if it’s open

(open-close programming option). Activating the input while

the gate is moving will reverse the gate.

Can be programmed to stop the gate while the gate is

moving (open-stop-close programming option).

Fire Department Input

Fully opens the gate when the input is activated. Overrides

the Mid-travel Stop and Auto Close Timer (if either is

programmed for the gate). The gate will lockout in the open

position without sounding the alarm. Press the STOP button

to release the lockout.

Open Input

Functions the same as the OPEN button.

Open Obstruction

While the gate is opening, any open obstruction signal will

cause the gate to stop, reverse a short distance, and then

stop again. The Auto Close Timer will be disabled, and a

renewed input will be required to start the gate again. Should

the gate be restarted and the obstacle signal occur again

prior to reaching a limit, the gate will stop again, lockout,

and sound the emergency alarm.

Close Obstruction

While the gate is closing, any close obstruction signal

will cause the gate to stop, reverse, and travel to the full

open position. Should a open obstruction input or an open

direction inherent entrapment condition occur prior to the

gate reaching the open limit, the operator will lockout and

sound the continuous tone alarm. Another close request

will be required to start the operator again. If after restart,

the overload or a close obstacle happens again before the

close limit is reached, the operator will lockout and sound

the alarm. If the auto close timer is set, when the close

obstruction input is cleared, the gate will close when the

auto close timer expires.

Reverse Input

If the reverse input is triggered while the gate is closing, the

gate will reverse to the full open position. If the Auto Close

Timer is set, when the reverse input is cleared, the gate will

close when the Auto Close Timer expires.

Open Loop

Functions the same as the OPEN button.

Reverse Loop

Functions the same as the reverse input.

Shadow/reset Loop

Only used with Swing Gates. Holds the gate fully open

or fully closed while triggered. If open, the gate closes

immediately when cleared if Anti-tailgate is enabled.

Operation Indications

During normal operation, the Controller’s displays will

indicate current operating conditions and status.

Power-up Display

When the Controller powers up, dashes will show on the

display, then the ﬁ rmware version number, then the gate

type (SL for slide and swing gates).

Exiting programming restarts the Controller. The power-up

display will show upon the restart.

Idle Condition

While the Controller is idling, waiting for a command, the

display will show circulating dashes.

For DC models only - Clockwise : Batteries discharging,

Counterclockwise : Batteries charging.

Last Gate Position/Condition

When the gate moves or stops, the display will show the

status for up to one minute.

• Stop is displayed as St

• Full Close is displayed as FC

• Full Open is displayed as FO

• Entrapment is displayed as En

Pre-start Delay

During the pre-start delay, the display will countdown the

number of seconds remaining before the operator starts.

Reverse Delay

If the gate travel direction is reversed from a user activation

or reversing device, and a reverse delay is set, the display

will count down the delay time in seconds before the

operator restarts.

Run Timer

While the gate is opening or closing, the number of seconds

running time is displayed.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 37 38

Comments to this Manuals

No comments

Linear SLC User Manual Page 28

Comments to this Manuals

Related products and manuals for Safety Linear SLC