Linear SLC User Manual download pdf (Page 17)

SLR • SLC • SLD Slide Gate Operator Installation Guide - 15 - 227968 Revision X19 8-11-2011

Advanced Controller Programming (Cont.)

Shadow Loop Open Prevention

If the shadow loop is triggered, it always prevents the gate from closing if

the Auto Close Timer activates or a CLOSE command is given while the

gate is at the full open position.

The controller can also be set to prevent the gate from opening if the

shadow loop is triggered while the gate is at the close limit position. This

prevents a swing gate from opening into a vehicle if it’s parked near the

gate on the inside.

Low Power Mode

This function is only used with DC slide gate Model SLD. The factory

default disables the Low Power Mode. When Low Power Mode is enabled,

and AC power fails, the controller will assume Low Power Mode after

60 seconds of gate inactivity. Low power mode turns off all accessory

power and indicators. Only inputs from the radio receiver, reverse loop,

open loop (optional by programming), ﬁ re department input, or restoring

AC power will wake the Controller from Low Power Mode. Programming

Mode can still be accessed while the Controller is awake in Low Power

Mode.

✓ NOTE: This function will only be displayed in Model SLD operators.

Power Failure Mode

This function is only used with DC slide gate Model SLD. The factory

default is set for Fail Safe, alternately the Controller can be set for Fail

Secure, Open Immediate, or Close Immediate.

• Fail Safe: If the AC power fails and the battery voltage drops below

approximately 22 Volts, 5 seconds later the operator will cycle open

if not already open. When AC power is restored, or the battery gets

charged by solar panels, the operator will resume normal operation

and auto-close if programmed to do so.

• Fail Secure: If the AC power fails and the battery voltage drops

below approximately 22 Volts, 5 seconds later the operator will

cycle closed if not already closed. When AC power is restored, or

the battery gets charged by solar panels, the operator will resume

normal operation.

✓ NOTE: Fail Safe and Fail Secure are disabled if Stagger Mode is

enabled.

• Open Immediate: If the AC power fails, the operator will cycle

open if not already open and cease operation. When AC power is

restored, the operator will resume normal operation and auto-close

if programmed to do so.

• Close Immediate: If the AC power fails, the operator will cycle

closed if not already closed and cease operation. When AC power is

restored, the operator will resume normal operation.

✓ NOTE: This function will only be displayed in Model SLD operators.

FUNCTION

SET TO FAIL SAFE MODE

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

POWER

FAILURE MODE

"FS"

SET TO FAIL SECURE MODE

DC MODELS

ONLY

SET TO OPEN IMMEDIATE MODE

SET TO CLOSE

IMMEDIATE MODE

FUNCTION

STANDARD OPERATION

SHADOW LOOP INHIBITS CLOSING ONLY

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

SHADOW LOOP

OPEN PREVENTION

"SP"

OPEN INHIBIT ON, SHADOW LOOP INHIBITS

OPENING AND CLOSING

FUNCTION

LOW POWER MODE DISABLED

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

LOW POWER

MODE

"LP"

LOW POWER MODE #1

RADIO WILL WAKE AND ACTIVATE,

REVERSE LOOP WILL JUST WAKE

DC MODELS

ONLY

LOW POWER MODE #2 - RADIO OR

OPEN LOOP WILL WAKE AND ACTIVATE,

REVERSE LOOP WILL JUST WAKE

THE FIRE DEPARTMENT INPUT

WILL ALWAYS WAKE UP CONTROLLER

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 37 38

Comments to this Manuals

No comments

Linear SLC User Manual Page 17

Comments to this Manuals

Related products and manuals for Safety Linear SLC