Linear SLC User Manual download pdf (Page 14)

SLR • SLC • SLD Slide Gate Operator Installation Guide - 12 - 227968 Revision X19 8-11-2011

Basic Controller Programming (Cont.)

Run Alarm and Pre-start Alarm

The factory default is Run Alarm on and a 3-second Pre-start Alarm. The

operator’s beeper will sound 3 seconds before the operator starts. The

options are:

• Run Alarm Off and Pre-start Alarm Off

• Run Alarm On and Pre-start Alarm Off

• Run Alarm On and Pre-start Alarm On for 1-9 Seconds

Maximum Open Direction Current Setting

To detect obstacles or mechanical problems with the gate, the operator

monitors its motor current. If the open current load exceeds the

programmed maximum load range number, the operator will stop, reverse

a short distance, then stop again. The Auto Close Timer will be disabled,

and another open request will be required to start the operator again. If

after restart, the overload or an open obstacle happens again before the

open limit is reached, the operator will lockout and sound the alarm.

To measure the motor load used during opening, while this function is

being displayed, push and hold the OPEN button to fully open the gate.

During movement, the motor current will be displayed as a load number

from 0 to 99. This number is useful for troubleshooting but not for setting

the motor current. At the end of travel, a different number will ﬂ ash. This

number indicates the range above and below the average motor current

during the run. Using the + and - buttons, set the programmed range

number so that a minimal force (50-75 lbs.) will activate a reversal should

an obstruction occur, but high enough to keep the gate moving under

normal conditions without interruption.

Maximum Close Direction Current Setting

To detect obstacles or mechanical problems with the gate, the

operator monitors its motor current. If the close current load exceeds

the programmed maximum load range number, the operator will stop,

reverse, and travel to the full open position. Should a open obstruction

input or an open direction inherent entrapment condition occur prior to

the gate reaching the open limit, the operator will lockout and sound the

continuous tone alarm. Another close request will be required to start the

operator again. If after restart, the overload or a close obstacle happens

again before the close limit is reached, the operator will lockout and

sound the alarm. If the auto close timer is set, when the close obstruction

input is cleared, the gate will close when the auto close timer expires.

To measure the motor load used during closing, while this function is

being displayed, push and hold the CLOSE button to close the gate.

During movement, the motor current will be displayed as a load number

from 0 to 99. This number is useful for troubleshooting but not used for

setting the motor current. At the end of travel, a different number will ﬂ ash.

This number indicates the range above and below the average motor

current during the run. Using the + and - buttons, set the programmed

range number so that a minimal force (50-75 lbs.) will activate a reversal

should an obstruction occur, but high enough to keep the gate moving

under normal conditions without interruption.

FUNCTION

SUGGESTED MINIMUM NUMBER WILL

FLASH, ADJUST TO THE PROPER FORCE

OPTIONS

MAX CLOSE

CURRENT

PRESS AND HOLD THE CLOSE BUTTON

UNTIL THE OPERATOR RUNS FULLY CLOSED

ENTER

PRESS ENTER TO STORE THE FORCE

"CC"

FUNCTION

SUGGESTED MINIMUM NUMBER WILL

FLASH, ADJUST TO THE PROPER FORCE

OPTIONS

MAX OPEN

CURRENT

PRESS AND HOLD THE OPEN BUTTON

UNTIL THE OPERATOR RUNS FULLY OPEN

ENTER

PRESS ENTER TO STORE THE FORCE

"OC"

FUNCTION

RUN ALARM ON

PRE-START ALARM OFF

RUN ALARM ON

PRE-START ALARM ON FOR 1 - 9 SECONDS

OPTIONS

RUN ALARM

PRE-START ALARM

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

RUN ALARM OFF

PRE-START ALARM OFF

"RP"

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 37 38

Comments to this Manuals

No comments

Linear SLC User Manual Page 14

Comments to this Manuals

Related products and manuals for Safety Linear SLC