Linear DVS-2400 User Manual download pdf (Page 27)

Black 0027

Black0027

12. ADVANCED PROGRAMMING

◆

To perform any of the advanced programming

steps, the Console must be in the Setup Mode.

◆

Each programming function is performed with

similar keystrokes. After the Console is in Setup

Mode, enter the programming step number,

press the [

HOME

] key (HOME = program), enter

the new value, and press the [

AWAY

] key

(AWAY = store). Follow the figures next to the

programming steps.

SETUP MODE

Start with the Console in Test Mode (Setup

Mode cannot be reached from any other mode).

From Test Mode, enter the master user code

then press [

TEST

✍

NOTE: Only the master user code can be used to

put the Console into the Setup Mode. The

restricted user codes cannot access Setup Mode.

❇

A “gong” and five “beeps” will sound, signaling

that the Console is in Setup Mode.

Hold the [

OFF

] key for three seconds when you

want to exit Setup Mode.

✍

NOTE: If the Console is left unattended in Setup

Mode, it will automatically switch back to Off Mode

after three minutes.

CONSOLE PROGRAMMING OPTIONS

STEP # PROGRAMMING FUNCTION POSSIBLE VALUES FACTORY VALUE INSTALLATION VALUE

25 ENTRY DELAY 20-255 SECONDS 30

26 EXIT DELAY 20-255 SECONDS 60

30 BURGLARY SIREN TIME 1-30 MINUTES 5

31 EMERGENCY SIREN TIME 1-30 MINUTES 5

32 FIRE SIREN TIME 1-30 MINUTES 5

40 AUTOMATION OUTPUT TIME 0-2500 SECONDS (0 = TOGGLE ON/OFF) 0

50 REMOTE ARMING MODE 2 = HOME MODE; 3 = AWAY MODE 3

51 REMOTE DISARMING MODE 0 = OFF MODE; 1 = CHIME MODE 0

61 ENTRY DELAY BEEPS 0 = OFF; 1 = ON 1

62 EXIT DELAY BEEPS 0 = OFF; 1 = ON 1

63 SILENT BURGLARY ALARM 0 = AUDIBLE; 1 = SILENT 0

64 SILENT EMERGENCY ALARM 0 = AUDIBLE; 1 = SILENT 0

65 QUICK ARMING 0 = OFF; 1 = ON 1

66 AUTO RESTORE 0 = OFF; 1 = ON 1

67 AUTO BYPASS 0 = OFF; 1 = ON 0

68 AUTOMATION MODE DURING ALARM

0 = FLASH (ENABLED BY FUNCTION 72)

1 = STEADY (ENABLED BY FUNCTION 72)

69 AUTOMATION BING TONE

0 = NO BINGS

1 = BINGS

70 REMOTE ARM/DISARM CHIRP

0 = NO CHIRPS

1 = CHIRPS (1 CHIRP = ARMED, 2 CHIRPS = DISARMED)

71 AUTOMATION FLASHES AFTER ALARM

0 = STANDARD

1 = FLASHING AFTER ALARM

72 AUTOMATION ACTIVE DURING ALARM

0 = STANDARD

1 = AUTOMATION ACTIVE DURING ALARM

(FLASH OR STEADY PROGRAMMED BY FUNCTION 68)

73 AUTOMATION ON WHILE ARMED

0 = STANDARD

1 = ON WHILE ARMED

74 AUTOMATION ON DURING EXIT/ENTRY

0 = STANDARD

1 = ON DURING EXIT/ENTRY DELAYS

75 AUTOMATION POLARITY 0 = + WHEN OFF; 1 = + WHEN ON 1

87 REMOTE ACCESS PASSWORD 6 DIGITS 987654

92 DURESS CODE 1-5 DIGITS REMOVED

93 RESTRICTED USER CODE #1 1-5 DIGITS REMOVED

94 RESTRICTED USER CODE #2 1-5 DIGITS REMOVED

95 RESTRICTED USER CODE #3 1-5 DIGITS REMOVED

96 RESTRICTED USER CODE #4 1-5 DIGITS REMOVED

97 RESTRICTED USER CODE #5 1-5 DIGITS REMOVED

98 PAGE ALERT USER CODE 1-5 DIGITS REMOVED

99 MASTER USER CODE 1-5 DIGITS 1234

Console Programming Table

HOME

TEST

= PROGRAM

= REMOVE

AWAY

= STORE

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 43 44

Comments to this Manuals

No comments

Linear DVS-2400 User Manual Page 27

Comments to this Manuals

Related products and manuals for Security access control systems Linear DVS-2400